Reznor RA 140 Manuel d'utilisateur télécharger pdf

Form I-OIL-HS, P/N 122407R2, Page 1



Applies to: Oil-Fired Heater Models OH 95, 140, 190;

RA 110, 140, 150, 235, 250; RV 225, 325

and a Model OT-250 Oil Tank

Installation Instructions for Oil Tank

Heater Stand, Option ST1

Form I-OIL-HS (Version A)

Obsoletes Form I-OIL-HS

Description/

Application

Option ST1 heater stand is designed to be eld-assembled to a Model OT-250

workbench oil tank for the purpose of supporting a Reznor

oil-red unit heater.

Adding the optional stand to the tank creates a unied tank/heater structure. Sus-

pension of the heater is not required when it is installed on the heater stand.

Select a location that will allow for required heater clearances as shown on the

rating plate and in the heater installation manual.

Components

Before beginning installation, verify components against the list below.

Check for damage. If damage is found, le a claim with the transporting agency.

Assembled Tank/Heater Structures using Option ST1

Model

RA235

Model

RV225

Option ST1

Heater Stand

Model OT-250

Workbench

Oil Tank

IMPORTANT

The Option ST1 heater

stand may only be used

with a Reznor

Model

OT-250 workbench oil

tank and one of the

Reznor heaters listed

below.

Model ......Sizes

OH ...........95, 140, 190

RA ...........110, 140, 150, 235, 250

RV ...........225, 325

DO NOT use this

heater stand with any

other models or sizes of

heaters.

Option STI Package P/N 202829

Components: Qty P/N

Structural

Parts and

Label for all

installations

Corner Post, 1-1/2” square tubing, approximately 8 feet long

4 202826

Tube Bracket Assembly, 2" square tubing

2 202828

Warning Label

2 121734

Front and Rear Support Angle 1-1/2” x 1-1/2” x 64" long

2 202827

Corner

Hardware for

all instalaltions

Hex Head Cap Screw, 1/2-13 x 3/4”

4 121593

Flat Washer, 1/2"

4 121595

Lock Washer, 1/2"

4 111306

Setscrew

Hardware for

all installations

Hex Head Cap Screw, 1/2-13 x 1-1/2”

8 121596

Jam Nut, 1/2 -13

8 45550

Angle Stops

and Hardware

(See

application

listed.)

Angle Stop, 1-1/2”x1-1/2”x1-1/4" lg w/ 3/8 & 7/32 holes - for OH & RA

4 202825

Hex Head Cap Screw, 5/16-18 x 3/4” - for OH and RA

4 16247

Hex Head Nut, 5/16-16 - for OH and RA

4 1035

Flat Washer, 5/16" - for OH and RA

4 27761

Lock Washer, 5/16 - for OH and RA

4 1333

Angle Stop, 1-1/2”x1-1/2”x1-1/4" lg w/ (2) 9/32 holes - for RV

4 202830

1/4-20 3/4" long F-point Screw - (8) for RV and (4) for RA 150, 250

8 114687

1 2 3 4

Résumé du contenu

Page 1 - IMPORTANT

Form I-OIL-HS, P/N 122407R2, Page 1Applies to: Oil-Fired Heater Models OH 95, 140, 190; RA 110, 140, 150, 235, 250; RV 225, 325 and a Model OT-250 O

Page 2 - Instructions

Form I-OIL-HS, Page 21. Model OT-250 Oil Tank – If the tank has not been installed, follow the handling instructions supplied with the tank. Contact t

Page 3 - Assembly

Form I-OIL-HS, P/N 122407R2, Page 3Slide the tube bracket assemblies over the top of each corner post.3. Prepare and Install the Tube Bracket Assembli

Page 4 - Hex Head Cap Screw

Form I-OIL-HS, Page 4At eachStandCornerPost -All Modelsand Sizesof HeaterModel OT250 Oil Tank(4) P/N 121596,1/2-13x1-1/2” lgHex Head Cap Screw(4) P/N