Reznor R6GP Option - Installation - Bottom Power Entry Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Radiateurs Reznor R6GP Option - Installation - Bottom Power Entry. Reznor R6GP Option - Installation - Bottom Power Entry User Manual [en] [pl] [cs] [de] Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 8
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
This kit is designed to allow passage of high and low
voltage wiring connections through the unit bottom
pan on R6GP Series units.
WARNING:
This kit is to be installed by a qualifi ed service
technician in accordance with these instructions
and all codes having jurisdiction. Failure to follow
these instructions could result in serious injury,
property damage, or death.
WARNING:
All electrical wiring must comply with the latest
edition of the National Electrical Code ANSI/
NFPA 70.
These instructions are primarily intended to assist
qualified individuals experienced in the proper
installation of this appliance. Some local codes require
licensed installation/service personnel for this type of
equipment.
This Kit Includes:
1) Parts kit:
a. 3/4” diameter, FMC straight connectors (2 ea.)
b. 3/4” diameter, insulator sleeve (2 ea.)
c. 3/4” diameter, insulator bushing (2 ea.)
d. 3/4” diameter, FMC (48” long)
e. 1-1/4” diameter, FMC straight connectors (2 ea.)
f. 1-1/4” diameter, insulator sleeve (2 ea.)
g. 1-1/4” diameter, insulator bushing
h. 1-1/4” diameter, FMC (24” long)
2) Bottom Power entry electrical box assembly
3) Bottom Power entry electrical box cover plate
4) 7/8” Diameter, plastic hole plug
5) 7/8” Diameter, plastic star bushing
6) ½” long #10 Screws (x ea.)
7) Zip-ties
8) Kit Instructions
Bottom Power Entry Kit
Installation Instructions
R6GP Model Series Accessory
Light Commercial Packaged Gas Electric Units
Field Supplied Items list:
1) Thread Sealant
2) Unit Disconnect
3) All conduit necessary for connections external to
the unit
Prior to beginning Installation, ensure the follow
conditions are met:
1) Read and understand the instructions for all
accessory kits to be installed with the unit and the
unit installation instructions
2) Unit is installed on roof-curb
3) No electrical power is connected to unit
4) Verify that input power supply is correct, verify with
unit rating label
5) Branch circuit protection to be used for unit is sized
in accordance with all applicable codes and unit
requirements
6) Perform all electrical set-up inspections called for
in unit Installation instructions
7) Verify kit contents to inventory list above
8) Verify all fi eld supplied items are on-hand for
installation
Vue de la page 0
1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - Installation Instructions

This kit is designed to allow passage of high and low voltage wiring connections through the unit bottom pan on R6GP Series units. WARNING:This kit is

Page 3 - Figure 3

3Installation Instructions:1. Remove unit control panel, blower access door and fi eld-wiring, electrical element access door are removed. (Refer to

Page 4 - Figure 7

47. On the left side of the unit control panel, behind the low-voltage connection box, remove the 1” diameter Heyco bushing from the base of the cont

Page 5 - Figure 9

513. Install the threaded insulator bushings onto both of the high voltage wiring conduits in the bottom power entry box and in the unit control panel

Page 6 - Figure 15. Bottom Power Kit

6HIGH VOLTAGE CONNECTIONSFOR UNIT CONTROL PANELHIGH VOLTAGE ACCESSFOR UNIT DISCONNECTBOTTOM POWER ENTRYBOX MOUNTING SCREWS(BOTH SIDES)LOW VOLTAGECONNE

Page 7 - Figure 17. Side View

7Figure 17. Side ViewLOW VOLTAGEKNOCK-OUTS7/8” x 27 1/2”6”3 3/8”10”14 1/2”HIGH VOLTAGE KNOCK-OUTS7/8” x 22” RADIUSLOW VOLTAGEENTRY AREAHIGH VOLTAGEENT

Page 8 - ¢708978k¤

¢708978k¤70897807089780Specifi cations and illustrations subject to change without notice and without incurring obligations. Printed in U.S.A. (03/0

Commentaires sur ces manuels

Pas de commentaire